Mippon soil
Wild-clay potential
Weak indication
Weak indication: no layer of Mippon shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Mippon soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Mippon gravelly fine sandy loam, 0 to 3 percent slopes (Cashmere Mountain Area, Washington, Parts of Chelan and Okanogan Counties) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 3% clay.
- Lowers the potential Low engineering plasticity index (0): little plastic behavior expected when wet.
- Lowers the potential The official series description calls the wet soil nonsticky and nonplastic.
- Note Thick enough to investigate (about 42 in (106 cm)).
- Note Typically starts within about 18 in (46 cm) of the surface.
- Lowers the potential High rock content (about 54% by volume) lowers its practical promise; the clay percentage applies only to the fine earth between the rocks.
Layer by layer
- Sandy layerH1 A gravelly fine sandy loam layer about 0 to 10 in down: about 7% clay, low plasticity when wet, very dark grayish brown when moist. Weak indication
- Sandy layerH2 A very cobbly loamy sand layer about 10 to 18 in down: about 4% clay, low plasticity when wet, brown when moist. Weak indication
- Sandy layerH3best layer An extremely cobbly loamy coarse sand layer about 18 to 60 in down: about 3% clay, low plasticity when wet, brown when moist. Weak indication
What it looks like raw
The sandy layer (H3), 18 to 60 in down in the typical profile: brown (10YR 4/3) dry, very dark grayish brown (10YR 3/2) moist; loose, nonsticky and nonplastic. Raw colour is not fired colour.
About the soil
- Parent material: recent alluvium.
- USDA family mineralogy: mixed.
- USDA family particle-size class: sandy-skeletal.
- Drainage: moderately well drained.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Washington, in these survey areas: Cashmere Mountain Area, Washington, Parts of Chelan and Okanogan Counties.
By state: wild clay in Washington.
USDA, distribution and extent: Mountainous areas of Chelan, Kittitas, and Yakima Counties, Washington, and northeastern Oregon; MLRAs 6 and 43C; small extent
USDA, geographic setting: Elevation--370 to 1475 m
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Bjork: Promising
- Cle Elum: Promising
- Cowiche: Possible
- Dragoon: Possible
- Georgecreek: Possible
- Kingmont: Possible
- Loneridge: Possible
- Morical: Possible
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 75%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Mippon gravelly fine sandy loam, 0 to 3 percent slopes, map unit 185 in Cashmere Mountain Area, Washington, Parts of Chelan and Okanogan Counties.
- Official Series Description: Mippon(revised 09/2019), established.
- Taxonomic class: Sandy-skeletal, mixed, frigid Fluventic Haploxerolls
- Rated with rule version 2026-09-28.1; the method is on the About page.