Limerick soil
Wild-clay potential
Weak indication
Weak indication: no layer of Limerick shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Limerick soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Limerick spot on the map
Rated from the USDA soil survey record for Limerick silt loam (Addison County, Vermont) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 5% clay.
- Lowers the potential Low engineering plasticity index (0): little plastic behavior expected when wet.
- Note Thick enough to investigate (about 37 in (94 cm)).
- Note Typically starts about 28 in (71 cm) down; expect real digging or look for cuts and banks.
- Missing data Rock fragment content is not reported.
Layer by layer
- Sandy layerH1 A silt loam layer about 0 to 5 in down: about 7% clay, low plasticity when wet, dark grayish brown when moist. Weak indication
- Sandy layerH2 A silt loam layer about 5 to 28 in down: about 6% clay, low plasticity when wet, olive gray when moist. Weak indication
- Sandy layerH3best layer A silt loam layer about 28 to 65 in down: about 5% clay, low plasticity when wet, dark gray when moist. Weak indication
What it looks like raw
The sandy layer (H3), 28 to 65 in down in the typical profile: dark gray (5Y 4/1). Raw colour is not fired colour.
About the soil
- Parent material: coarse-silty alluvium.
- USDA family mineralogy: mixed.
- USDA family particle-size class: coarse-silty.
- Drainage: poorly drained.
- Rated hydric (wetland) soil; often saturated and protected.
Where it is mapped
Seen on the map as the most common soil in 2 map units in Vermont, in these survey areas: Addison County, Vermont.
By state: wild clay in Vermont.
USDA, distribution and extent: Connecticut, Massachusetts, New Hampshire, New York, and Vermont; MLRAs 142, 144A, and 145. The series is of moderate extent.
USDA, geographic setting: Limerick soils are on the flood plains of major rivers and their larger tributaries. In some places they are on the flood plains of small streams. They may be on broad flat areas or in shallow depressions. The soils formed in recent alluvial deposits that are dominantly silt and very fine sand. Mean annual temperature ranges from about 45 through 52 degrees F. (7 through 11 degrees C.), and mean annual precipitation ranges from 30 through 50 inches (762 through 1270 millimeters). The frost-free season ranges from 105 through 180 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Covington: Strong lead
- Livingston: Strong lead
- Melrose: Strong lead
- Swanton: Strong lead
- Vergennes: Strong lead
- Elmwood: Promising
- Canandaigua: Possible
- Farmington: Possible
See it on the map
Open a Limerick spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Limerick silt loam, map unit Le in Addison County, Vermont.
- Official Series Description: Limerick(revised 03/2010), established.
- Taxonomic class: Coarse-silty, mixed, superactive, nonacid, mesic Fluvaquentic Endoaquepts
- Rated with rule version 2026-09-28.1; the method is on the About page.