Inkler soil
Wild-clay potential
Weak indication
Weak indication: no layer of Inkler shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Inkler soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Inkler stony fine sandy loam, 30 to 60 percent slopes (Cashmere Mountain Area, Washington, Parts of Chelan and Okanogan Counties) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 10% clay.
- Lowers the potential Low engineering plasticity index (2.5): little plastic behavior expected when wet.
- Note The official series description calls the wet soil slightly sticky and slightly plastic.
- Note Thick enough to investigate (about 19 in (49 cm)).
- Note Typically starts within about 10 in (25 cm) of the surface.
- Lowers the potential High rock content (about 47% by volume) lowers its practical promise; the clay percentage applies only to the fine earth between the rocks.
Layer by layer
- Sandy layerH1 A stony ashy fine sandy loam layer about 0 to 4 in down: about 8% clay, low plasticity when wet, gray when moist. Weak indication
- Sandy layerH2 A very cobbly ashy sandy loam layer about 4 to 10 in down: about 10% clay, low plasticity when wet, pale brown when moist. Weak indication
- Sandy layerH3best layer A very stony ashy sandy loam layer about 10 to 29 in down: about 10% clay, low plasticity when wet, pale brown when moist. Weak indication
- Sandy layerH4 An extremely cobbly sandy loam layer about 29 to 44 in down: about 5% clay, low plasticity when wet, light brownish gray when moist. Weak indication
- BedrockH5 Unweathered bedrock about 44 to 48 in down: no clay layer to dig. Weak indication
What it looks like raw
The sandy layer (H3), 10 to 29 in down in the typical profile: pale brown (10YR 6/3), dark brown (10YR 3/3) moist; soft, friable, slightly sticky and slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: colluvium derived from gneiss and schist with mantle of volcanic ash.
- USDA family particle-size class: loamy-skeletal.
- Drainage: well drained.
- Lithic bedrock typically about 44 in (112 cm) down.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Washington, in these survey areas: Cashmere Mountain Area, Washington, Parts of Chelan and Okanogan Counties.
By state: wild clay in Washington.
USDA, distribution and extent: Northeastern Washington. MLRA 43A, 6. The Inkler series is of moderate extent.
USDA, geographic setting: Landforms - moraines, hillslopes and mountain slopes
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Bjork: Promising
- Cle Elum: Promising
- Cowiche: Possible
- Dragoon: Possible
- Georgecreek: Possible
- Kingmont: Possible
- Loneridge: Possible
- Morical: Possible
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 75%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Inkler stony fine sandy loam, 30 to 60 percent slopes, map unit 142 in Cashmere Mountain Area, Washington, Parts of Chelan and Okanogan Counties.
- Official Series Description: Inkler(revised 01/2016), established.
- Taxonomic class: Loamy-skeletal, isotic, frigid Andic Haploxerepts
- Rated with rule version 2026-09-28.1; the method is on the About page.