Darwin soil
Wild-clay potential
Strong lead
Strong lead: a clayey layer typically about 40 to 80 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Darwin soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Darwin silty clay, 0 to 2 percent slopes, occasionally flooded (Pike County, Illinois) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 39% clay in the fine-earth portion.
- Raises the potential High engineering plasticity index (28): USDA's estimate suggests plastic behavior when wet.
- Note Thick enough to investigate (about 40 in (101 cm)).
- Note Typically starts about 40 in (102 cm) down; expect real digging or look for cuts and banks.
- Missing data Rock fragment content is not reported.
- Note High shrink-swell (linear extensibility about 6.8%): often very plastic, and prone to cracking as it dries.
- Note USDA reports about 8% calcium carbonate; lime in a clay body deserves testing.
Layer by layer
- Clay-rich layerH1 A silty clay layer about 0 to 12 in down: about 43% clay, high plasticity when wet, very dark gray when moist. Strong lead
- Clay-rich layerH2 A silty clay layer about 12 to 40 in down: about 52% clay, high plasticity when wet, dark gray when moist. Strong lead
- Clay-rich layerH3best layer A silty clay loam layer about 40 to 80 in down: about 39% clay, high plasticity when wet, gray when moist. Strong lead
What it looks like raw
The clay-rich layer (H3), 40 to 80 in down in the typical profile: gray (5Y 5/1); firm. Raw colour is not fired colour.
About the soil
- Parent material: clayey alluvium.
- USDA family mineralogy: smectitic. Smectite-rich clays are usually very plastic and shrink a lot as they dry.
- USDA family particle-size class: fine.
- Drainage: poorly drained.
- Rated hydric (wetland) soil; often saturated and protected.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Illinois, in these survey areas: Pike County, Illinois.
By state: wild clay in Illinois.
USDA, distribution and extent: Darwin soils are in Illinois, Missouri and Iowa. MLRAs 108, 113, 114, 115, 120, 131, 134. The extent is moderate.
USDA, geographic setting: Darwin soils are on nearly level flood plains of large streams. Slope gradients commonly are less than 1 percent but range from 0 to 2 percent. Darwin soils formed in fine-textured alluvium. Mean annual temperature ranges from 45 to 57 degrees F., mean annual precipitation ranges from 30 to 48 inches, frost free days range from 140 to 200 days, and elevation ranges from 340 to 1250 feet above sea level.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Elco: Strong lead
- Ipava: Strong lead
- Keswick: Strong lead
- Titus: Strong lead
- Ambraw: Promising
- Baylis: Promising
- Beaucoup: Promising
- Bethalto: Promising
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Darwin silty clay, 0 to 2 percent slopes, occasionally flooded, map unit 8071A in Pike County, Illinois.
- Official Series Description: Darwin(revised 06/2015), established.
- Taxonomic class: Fine, smectitic, mesic Fluvaquentic Vertic Endoaquolls
- Rated with rule version 2026-09-28.1; the method is on the About page.