Dan River soil
Wild-clay potential
Possible
Possible: a loamy layer with some clay typically about 18 to 46 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Dan River soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Dan River spot on the map
Rated from the USDA soil survey record for Dan River loam, 0 to 2 percent slopes, frequently flooded (Forsyth County, North Carolina) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 27% clay. It may need settling or refining to become a clay body.
- Note Moderate engineering plasticity index (11.5).
- Note The official series description calls the wet soil slightly sticky and slightly plastic.
- Note Thick enough to investigate (about 28 in (71 cm)).
- Note Typically starts within about 18 in (46 cm) of the surface.
- Note Few rock fragments (about 2% by volume).
Layer by layer
- TopsoilAp A loam layer about 0 to 18 in down: about 19% clay, moderate plasticity when wet, dark yellowish brown when moist. Possible
- Loamy layerBwbest layer A loam layer about 18 to 46 in down: about 27% clay, moderate plasticity when wet, dark yellowish brown when moist. Possible
- Sandy layerC1 A sandy loam layer about 46 to 55 in down: about 18% clay, moderate plasticity when wet, yellowish brown when moist. Weak indication
- Loamy layerC2 A clay loam layer about 55 to 72 in down: about 30% clay, moderate plasticity when wet, yellowish brown when moist. Weak indication
- Loamy layerC3 A loam layer about 72 to 80 in down: about 27% clay, moderate plasticity when wet, yellowish brown when moist. Weak indication
What it looks like raw
The loamy layer (Bw), 18 to 46 in down in the typical profile: dark yellowish brown (10YR 4/4); friable, slightly sticky, slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: loamy alluvium derived from igneous and metamorphic rock.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in North Carolina, in these survey areas: Forsyth County, North Carolina.
By state: wild clay in North Carolina.
USDA, distribution and extent: Distribution: Virginia and North Carolina
USDA, geographic setting: Landscape: Piedmont
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Appling: Strong lead
- Banister: Strong lead
- Casville: Strong lead
- Cecil: Strong lead
- Clifford: Strong lead
- Enon: Strong lead
- Fairview: Strong lead
- Hiwassee: Strong lead
See it on the map
Open a Dan River spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Dan River loam, 0 to 2 percent slopes, frequently flooded, map unit DaA in Forsyth County, North Carolina.
- Official Series Description: Dan River(revised 04/2026), established.
- Taxonomic class: Fine-loamy, mixed, active, mesic Oxyaquic Dystrudepts
- Rated with rule version 2026-09-28.1; the method is on the About page.