Brisky soil
Wild-clay potential
Weak indication
Weak indication: no layer of Brisky shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Brisky soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Brisky-Rock outcrop complex, 30 to 60 percent slopes (Cashmere Mountain Area, Washington, Parts of Chelan and Okanogan Counties) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 10% clay.
- Lowers the potential Low engineering plasticity index (2.5): little plastic behavior expected when wet.
- Lowers the potential The official series description calls the wet soil nonsticky and nonplastic.
- Note Moderate thickness (about 6 in (15 cm)).
- Note Typically starts within about 4 in (10 cm) of the surface.
- Lowers the potential High rock content (about 40% by volume) lowers its practical promise; the clay percentage applies only to the fine earth between the rocks.
Layer by layer
- Sandy layerH1 A very gravelly sandy loam layer about 0 to 4 in down: about 10% clay, low plasticity when wet, brown when moist. Weak indication
- Sandy layerH2best layer A very gravelly sandy loam layer about 4 to 10 in down: about 10% clay, low plasticity when wet, light yellowish brown when moist. Weak indication
- BedrockH3 Unweathered bedrock about 10 to 14 in down: no clay layer to dig. Weak indication
What it looks like raw
The sandy layer (H2), 4 to 10 in down in the typical profile: light yellowish brown (10YR 6/4), yellowish brown (10YR 4/4) moist; slightly hard, firm, nonsticky and nonplastic. Raw colour is not fired colour.
About the soil
- Parent material: colluvium from sandstone mixed with volcanic ash and loess.
- USDA family mineralogy: mixed.
- USDA family particle-size class: loamy-skeletal.
- Drainage: well drained.
- Lithic bedrock typically about 10 in (25 cm) down.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Washington, in these survey areas: Cashmere Mountain Area, Washington, Parts of Chelan and Okanogan Counties.
By state: wild clay in Washington.
USDA, distribution and extent: East slopes of the Cascade Mountains in southeastern Chelan County and northern Kittitas Counties, Washington. This series is of moderate extent.
USDA, geographic setting: Brisky soils are on mountainsides and ridgetops with southerly aspects and have slopes of 30 to 65 percent. These soils formed in colluvium from sandstone, mixed with volcanic ash and loess. Elevations are 1,500 to 4,100 feet. These soils are in climate with warm dry summers and cool winters. The average annual precipitation is 20 to 32 inches. The mean January temperature is about 26 degrees F, the mean July temperature is about 66 degrees F, and the mean annual temperature is about 43 to 47 degrees F. The frost-free season is about 110 to 130 days. Growing season at 28 degrees F is 140 to 180 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Bjork: Promising
- Cle Elum: Promising
- Cowiche: Possible
- Dragoon: Possible
- Georgecreek: Possible
- Kingmont: Possible
- Loneridge: Possible
- Morical: Possible
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 65%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Brisky-Rock outcrop complex, 30 to 60 percent slopes, map unit 51 in Cashmere Mountain Area, Washington, Parts of Chelan and Okanogan Counties.
- Official Series Description: Brisky(revised 12/1999), established.
- Taxonomic class: Loamy-skeletal, mixed, superactive, mesic Lithic Ultic Haploxerolls
- Rated with rule version 2026-09-28.1; the method is on the About page.