Almac soil
Wild-clay potential
Weak indication
Weak indication: no layer of Almac shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Almac soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Almac fine sandy loam, 3 to 30 percent slopes (Cashmere Mountain Area, Washington, Parts of Chelan and Okanogan Counties) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 15% clay.
- Lowers the potential Low engineering plasticity index (2.5): little plastic behavior expected when wet.
- Note The official series description calls the wet soil slightly sticky and slightly plastic.
- Note Thick enough to investigate (about 27 in (69 cm)).
- Note Typically starts within about 23 in (58 cm) of the surface.
- Lowers the potential Noticeable rock fragments (about 27% by volume); screening would be needed and the clay percentage applies to the fine earth only.
Layer by layer
- Sandy layerH1 An ashy fine sandy loam layer about 0 to 3 in down: about 9% clay, low plasticity when wet, light gray when moist. Weak indication
- Sandy layerH2 An ashy fine sandy loam layer about 3 to 23 in down: about 11% clay, low plasticity when wet. Weak indication
- Sandy layerH3best layer A gravelly loam layer about 23 to 50 in down: about 15% clay, low plasticity when wet, light yellowish brown when moist. Weak indication
- Sandy layerH4 A gravelly fine sandy loam layer about 50 to 63 in down: about 8% clay, low plasticity when wet. Weak indication
What it looks like raw
The sandy layer (H3), 23 to 50 in down in the typical profile: hard, firm, slightly sticky and slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: volcanic ash over colluvium and residuum derived from schist and gneiss.
- USDA family particle-size class: ashy over loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 2 map units in Washington, in these survey areas: Cashmere Mountain Area, Washington, Parts of Chelan and Okanogan Counties.
By state: wild clay in Washington.
USDA, distribution and extent: East slopes of the Cascade mountains in west central Chelan County, Washington. This series is of moderate extent.
USDA, geographic setting: Almac soils are on mountain ridgetops and back slopes. They formed in volcanic ash over residuum and colluvium from schist, phyllite, and gneiss. Elevations are 3,200 to 6,000 feet. The soil is in a climate with warm, dry summers and cold, moist winters. The average annual precipitation is 35 to 55 inches. The mean January temperature is about 19 degrees F., the mean July temperature is about 58 degrees F., and the mean annual air temperature is 38 to 40 degrees F. The growing season at 28 degrees F. is about 100 to 140 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Bjork: Promising
- Cle Elum: Promising
- Cowiche: Possible
- Dragoon: Possible
- Georgecreek: Possible
- Kingmont: Possible
- Loneridge: Possible
- Morical: Possible
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Almac fine sandy loam, 3 to 30 percent slopes, map unit 2 in Cashmere Mountain Area, Washington, Parts of Chelan and Okanogan Counties.
- Official Series Description: Almac(revised 03/2002), established.
- Taxonomic class: Ashy over loamy, glassy over isotic Xeric Vitricryands
- Rated with rule version 2026-09-28.1; the method is on the About page.