Alanthus soil
Wild-clay potential
Possible
Possible: a loamy layer with some clay typically about 7 to 28 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Alanthus soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Alanthus spot on the map
Rated from the USDA soil survey record for Alanthus silt loam, 7 to 15 percent slopes (Fauquier County, Virginia) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clay-enriched layer: about 30% clay in the fine-earth portion.
- Note Moderate engineering plasticity index (18).
- Lowers the potential The official series description calls the wet soil slightly sticky and nonplastic.
- Note Thick enough to investigate (about 21 in (53 cm)).
- Note Typically starts within about 7 in (18 cm) of the surface.
- Note Few rock fragments (about 3% by volume).
Layer by layer
- Sandy layerH1 A silt loam layer about 0 to 7 in down: about 15% clay, moderate plasticity when wet, reddish brown when moist. Weak indication
- Loamy layerH2best layer A silty clay loam layer about 7 to 28 in down: about 30% clay, moderate plasticity when wet, reddish brown when moist. Possible
- Loamy layerH3 A silty clay loam layer about 28 to 42 in down: about 30% clay, moderate plasticity when wet, yellowish red when moist. Possible
- Sandy layerH4 A silt loam layer about 42 to 84 in down: about 15% clay, moderate plasticity when wet, strong brown when moist. Weak indication
What it looks like raw
The loamy layer (H2), 7 to 28 in down in the typical profile: reddish brown (2.5YR 4/4); friable, slightly sticky and nonplastic. Raw colour is not fired colour.
About the soil
- Parent material: residuum weathered from greenstone.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Virginia, in these survey areas: Fauquier County, Virginia.
By state: wild clay in Virginia.
USDA, distribution and extent: Virginia, Maryland, Pennsylvania. The series is of moderate extent.
USDA, geographic setting: Summits and backslopes on ridges and hill in the Blue Ridge Foothills. Slope ranges from 0 to 45 percent. Soils form in residuum from metabasalt and greenstone schist. Mean annual precipitation ranges from 38 to 48 inches and mean annual temperature ranges 50 to 58 degrees F.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Albano: Strong lead
- Appling: Strong lead
- Cecil: Strong lead
- Clover: Strong lead
- Dulles: Strong lead
- Fletcherville: Strong lead
- Jackland: Strong lead
- Kelly: Strong lead
See it on the map
Open a Alanthus spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Alanthus silt loam, 7 to 15 percent slopes, map unit 43C in Fauquier County, Virginia.
- Official Series Description: Alanthus(revised 01/2006), established.
- Taxonomic class: Fine-loamy, mixed, active, mesic Ultic Hapludalfs
- Rated with rule version 2026-09-28.1; the method is on the About page.