Snyderville soil
Wild-clay potential
Weak indication
Weak indication: no layer of Snyderville shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Snyderville soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Snyderville spot on the map
Rated from the USDA soil survey record for Snyderville cobbly loam, 5 to 10 percent slopes (Summit Area, Utah, Parts of Summit, Salt Lake and Wasatch Counties) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 3% clay.
- Lowers the potential Low engineering plasticity index (0): little plastic behavior expected when wet.
- Note Thick enough to investigate (about 25 in (63 cm)).
- Note Typically starts about 35 in (89 cm) down; expect real digging or look for cuts and banks.
- Lowers the potential High rock content (about 70% by volume) lowers its practical promise; the clay percentage applies only to the fine earth between the rocks.
Layer by layer
- TopsoilA1 A cobbly loam layer about 0 to 10 in down: about 20% clay, moderate plasticity when wet, very dark brown when moist. Weak indication
- TopsoilA2 A cobbly loam layer about 10 to 16 in down: about 20% clay, moderate plasticity when wet, very dark grayish brown when moist. Weak indication
- Clay subsoilBt A very cobbly loam layer about 16 to 28 in down: about 25% clay, moderate plasticity when wet, dark brown when moist. Weak indication
- Sandy layer2C A very cobbly loamy sand layer about 28 to 35 in down: about 8% clay, low plasticity when wet, brown when moist. Weak indication
- Sandy layer3Cbest layer An extremely cobbly sand layer about 35 to 60 in down: about 3% clay, low plasticity when wet, brown when moist. Weak indication
What it looks like raw
The sandy layer (3C), 35 to 60 in down in the typical profile: brown (7.5YR 4/3); extremely cobbly sand; loose. Raw colour is not fired colour.
About the soil
- Parent material: alluvium and outwash derived from sandstone, conglomerate and quartzite.
- USDA family mineralogy: mixed.
- USDA family particle-size class: loamy-skeletal.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 2 map units in Utah, in these survey areas: Summit Area, Utah, Parts of Summit, Salt Lake and Wasatch Counties.
By state: wild clay in Utah.
USDA, distribution and extent: North central Utah and southestern Idaho. LRR B and E, MLRA 13 and 47. This series is of moderate extent.
USDA, geographic setting: Parent material: Alluvium or outwash derived from quartzite and sedimentary rocks.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Manila: Strong lead
- Fewkes: Promising
- Hades: Promising
- Harter: Promising
- Ayoub: Possible
- Dastrup: Possible
- Echocreek: Possible
- Richsum: Possible
See it on the map
Open a Snyderville spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Snyderville cobbly loam, 5 to 10 percent slopes, map unit 175 in Summit Area, Utah, Parts of Summit, Salt Lake and Wasatch Counties.
- Official Series Description: Snyderville(revised 06/2010), established.
- Taxonomic class: Loamy-skeletal, mixed, superactive, frigid Pachic Argixerolls
- Rated with rule version 2026-09-28.1; the method is on the About page.