Riverview soil
Wild-clay potential
Possible
Possible: a loamy layer with some clay typically about 18 to 46 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Riverview soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Riverview spot on the map
Rated from the USDA soil survey record for Riverview sandy loam, 0 to 2 percent slopes, frequently flooded (Randolph County, North Carolina) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 27% clay. It may need settling or refining to become a clay body.
- Note Moderate engineering plasticity index (11.5).
- Note Thick enough to investigate (about 28 in (71 cm)).
- Note Typically starts within about 18 in (46 cm) of the surface.
- Note Few rock fragments (about 2% by volume).
Layer by layer
- TopsoilAp A loam layer about 0 to 18 in down: about 19% clay, moderate plasticity when wet, dark yellowish brown when moist. Possible
- Loamy layerBwbest layer A loam layer about 18 to 46 in down: about 27% clay, moderate plasticity when wet, dark yellowish brown when moist. Possible
- Sandy layerC1 A sandy loam layer about 46 to 55 in down: about 18% clay, moderate plasticity when wet, brownish yellow when moist. Weak indication
- Loamy layerC2 A clay loam layer about 55 to 72 in down: about 30% clay, moderate plasticity when wet, brownish yellow when moist. Possible
- Loamy layerC3 A loam layer about 72 to 80 in down: about 27% clay, moderate plasticity when wet, brownish yellow when moist. Weak indication
What it looks like raw
The loamy layer (Bw), 18 to 46 in down in the typical profile: dark yellowish brown (10YR 3/4); friable. Raw colour is not fired colour.
About the soil
- Parent material: loamy alluvium derived from igneous and metamorphic rock.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in North Carolina, in these survey areas: Randolph County, North Carolina.
By state: wild clay in North Carolina.
USDA, distribution and extent: Coastal Plain and Southern Piedmont of Alabama,
USDA, geographic setting: Riverview soils are on high parts of flood plains of rivers and streams draining the Coastal Plain and Southern Piedmont. Slopes range from 0 to 5 percent. They formed in loamy alluvium. The average annual air temperature ranges from 61 to 68 degrees F. and average annual precipitation ranges from 50 to 60 inches.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Appling: Strong lead
- Badin: Strong lead
- Cecil: Strong lead
- Coronaca: Strong lead
- Davidson: Strong lead
- Dorian: Strong lead
- Helena: Strong lead
- Mecklenburg: Strong lead
See it on the map
Open a Riverview spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Riverview sandy loam, 0 to 2 percent slopes, frequently flooded, map unit RvA in Randolph County, North Carolina.
- Official Series Description: Riverview(revised 08/2008), established.
- Taxonomic class: Fine-loamy, mixed, active, thermic Fluventic Dystrudepts
- Rated with rule version 2026-09-28.1; the method is on the About page.