Raypol soil
Wild-clay potential
Weak indication
Weak indication: no layer of Raypol shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Raypol soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Raypol silt loam (Delaware County, New York) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 2% clay.
- Lowers the potential Low engineering plasticity index (0): little plastic behavior expected when wet.
- Note Thick enough to investigate (about 32 in (81 cm)).
- Note Typically starts about 40 in (102 cm) down; expect real digging or look for cuts and banks.
- Lowers the potential High rock content (about 50% by volume) lowers its practical promise; the clay percentage applies only to the fine earth between the rocks.
Layer by layer
- TopsoilAp A silt loam layer about 0 to 5 in down: about 12% clay, low plasticity when wet, very dark brown when moist. Weak indication
- Sandy layerBA A silt loam layer about 5 to 10 in down: about 12% clay, low plasticity when wet, very dark brown when moist. Weak indication
- Sandy layerBw1 A very fine sandy loam layer about 10 to 13 in down: about 10% clay, low plasticity when wet, dark yellowish brown when moist. Weak indication
- Sandy layerBw2 A loam layer about 13 to 21 in down: about 12% clay, low plasticity when wet, olive brown when moist. Weak indication
- Sandy layer2C1 A stratified loamy fine sand to fine sandy loam layer about 21 to 27 in down: about 7% clay, low plasticity when wet, light olive brown when moist. Weak indication
- Sandy layer2C2 A loamy fine sand layer about 27 to 32 in down: about 5% clay, low plasticity when wet, dark grayish brown when moist. Weak indication
- Sandy layer2C3 A very gravelly loamy fine sand layer about 32 to 40 in down: about 5% clay, low plasticity when wet, light olive brown when moist. Weak indication
- Sandy layer2C4best layer A very gravelly sand layer about 40 to 72 in down: about 2% clay, low plasticity when wet, light olive brown when moist. Weak indication
What it looks like raw
The sandy layer (2C4), 40 to 72 in down in the typical profile: light olive brown (2.5Y 5/4); loose. Raw colour is not fired colour.
About the soil
- Parent material: loamy over sandy and gravelly glaciofluvial deposits derived mainly from acid sedimentary rocks.
- USDA family mineralogy: mixed.
- USDA family particle-size class: coarse-loamy over sandy or sandy-skeletal.
- Drainage: poorly drained.
- Rated hydric (wetland) soil; often saturated and protected.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in New York, in these survey areas: Delaware County, New York.
By state: wild clay in New York.
USDA, distribution and extent: Glaciofluvial landforms in Connecticut, Rhode Island and New York; MLRAs 140, 144A and 145. The series is of moderate extent.
USDA, geographic setting: Raypol soils are nearly level to gently sloping soils in drainageways and low-lying areas on terraces and plains. Slope ranges from 0 to 5 percent. The soils formed in loamy over sandy and gravelly glaciofluvial materials derived mainly from acid cystalline and sedimentary rocks. Mean annual temperature is 45 to 54 degrees F., mean annual precipitation is 37 to 50 inches and the growing season is 130 to 195 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Barbour: Weak indication
- Basher: Weak indication
- Bath: Weak indication
- Bucksport: Weak indication
- Carlisle: Weak indication
- Chenango: Weak indication
- Deposit: Weak indication
- Elka: Weak indication
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 80%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Raypol silt loam, map unit Rb in Delaware County, New York.
- Official Series Description: Raypol(revised 05/1999), established.
- Taxonomic class: Coarse-loamy over sandy or sandy-skeletal, mixed, active, acid, mesic Aeric Endoaquepts
- Rated with rule version 2026-09-28.1; the method is on the About page.