Nyssaton soil
Wild-clay potential
Weak indication
Weak indication: no layer of Nyssaton shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Nyssaton soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Nyssaton spot on the map
Rated from the USDA soil survey record for Nyssaton silt loam, 0 to 1 percent slopes (Canyon Area, Idaho) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 13% clay.
- Note Moderate engineering plasticity index (8).
- Note The official series description calls the wet soil slightly sticky and slightly plastic.
- Note Thick enough to investigate (about 49 in (124 cm)).
- Note Typically starts within about 11 in (28 cm) of the surface.
- Missing data Rock fragment content is not reported.
- Note USDA reports about 18% calcium carbonate; lime in a clay body deserves testing.
Layer by layer
- TopsoilAp A silt loam layer about 0 to 11 in down: about 13% clay, moderate plasticity when wet, light brownish gray when moist. Weak indication
- Sandy layerBkbest layer A silt loam layer about 11 to 60 in down: about 13% clay, moderate plasticity when wet, white when moist. Weak indication
What it looks like raw
The sandy layer (Bk), 11 to 60 in down in the typical profile: white (2.5Y 8/2), grayish brown (10YR 5/2) moist; soft, very friable, slightly sticky and slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: lacustrine deposits and/or loess and/or silty alluvium.
- USDA family mineralogy: mixed.
- USDA family particle-size class: coarse-silty.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 5 map units in Idaho, in these survey areas: Canyon Area, Idaho.
By state: wild clay in Idaho.
USDA, distribution and extent: Southwestern Idaho and central Washington. Nyssaton soils are of moderate extent.
USDA, geographic setting: Nyssaton soils are level to moderately steep on low and medium terraces and steep and very steep terrace escarpments in Washington at elevations of 1,000 to 2,700 feet. Slopes range from 0 to 30 percent in Idaho and up to 65 percent in Washington, but are dominantly less than 7 percent. These soils formed in silty calcareous laminated lacustrine material influenced in the upper part by local alluvium and loess. The climate is cool and moist in the winter and hot and dry summer. Average annual precipitation ranges from 7 to 12 inches. Average annual temperature ranges from 48 to 52 degrees F. Frost-free period is 130 to 180 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Catherine: Promising
- Elijah: Promising
- Greenleaf: Promising
- Nannyton: Promising
- Baldock: Possible
- Chance: Possible
- Draper: Possible
- Harpt: Possible
See it on the map
Open a Nyssaton spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 95%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Nyssaton silt loam, 0 to 1 percent slopes, map unit NsA in Canyon Area, Idaho.
- Official Series Description: Nyssaton, established.
- Taxonomic class: Coarse-silty, mixed, superactive, mesic Xeric Haplocalcids
- Rated with rule version 2026-09-28.1; the method is on the About page.