Letha soil
Wild-clay potential
Weak indication
Weak indication: no layer of Letha shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Letha soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Letha fine sandy loam, 0 to 1 percent slopes (Canyon Area, Idaho) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 10% clay.
- Lowers the potential Low engineering plasticity index (6): little plastic behavior expected when wet.
- Note The official series description calls the wet soil slightly sticky and slightly plastic.
- Note Thick enough to investigate (about 35 in (89 cm)).
- Note Typically starts within about 5 in (13 cm) of the surface.
- Note Few rock fragments (about 6% by volume).
- Note USDA reports about 10% calcium carbonate; lime in a clay body deserves testing.
Layer by layer
- TopsoilA A fine sandy loam layer about 0 to 5 in down: about 8% clay, low plasticity when wet, light gray when moist. Weak indication
- Sandy layerC1best layer A fine sandy loam layer about 5 to 40 in down: about 10% clay, low plasticity when wet, pale yellow when moist. Weak indication
- Sandy layer2C2 A sand layer about 40 to 58 in down: about 6% clay, low plasticity when wet. Weak indication
What it looks like raw
The sandy layer (C1), 5 to 40 in down in the typical profile: pale yellow (2.5Y 7/3), olive brown (2.5Y 4/3), and grayish brown (2.5Y 5/2) moist; friable, slightly sticky and slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: mixed alluvium.
- USDA family mineralogy: mixed.
- USDA family particle-size class: coarse-loamy.
- Drainage: somewhat poorly drained.
Where it is mapped
Seen on the map as the most common soil in 3 map units in Idaho, in these survey areas: Canyon Area, Idaho.
By state: wild clay in Idaho.
USDA, distribution and extent: Southwestern Idaho and southeastern Oregon. Moderately extensive.
USDA, geographic setting: Letha soils are on low terraces at elevations of 610 to 1070 meters. Slopes range from 0 to about 3 percent. The soils formed in moderately coarse textured alluvium derived from coarse grained acid igneous rocks. The average annual precipitation is 200 to 300 millimeters, including 300 to 910 mm of snow. Average annual temperature is 8 to 11 degrees C. Frost-free period is 140 to 160 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Catherine: Promising
- Elijah: Promising
- Greenleaf: Promising
- Nannyton: Promising
- Baldock: Possible
- Chance: Possible
- Draper: Possible
- Harpt: Possible
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 90%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Letha fine sandy loam, 0 to 1 percent slopes, map unit LsA in Canyon Area, Idaho.
- Official Series Description: Letha(revised 08/2021), established.
- Taxonomic class: Coarse-loamy, mixed, superactive, calcareous, mesic Aeric Halaquepts
- Rated with rule version 2026-09-28.1; the method is on the About page.