Goldston soil
Wild-clay potential
Weak indication
Weak indication: no layer of Goldston shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Goldston soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Goldston spot on the map
Rated from the USDA soil survey record for Goldston very channery silt loam, 4 to 15 percent slopes (Davidson County, North Carolina) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Bedrock or unweathered rock, not a soil layer to dig for clay.
Layer by layer
- TopsoilA A very channery silt loam layer about 0 to 1 in down: about 13% clay, low plasticity when wet, dark grayish brown when moist. Weak indication
- Sandy layerE A very channery silt loam layer about 1 to 7 in down: about 13% clay, low plasticity when wet, brown when moist. Weak indication
- Loamy layerBw A very channery silt loam layer about 7 to 16 in down: about 19% clay, low plasticity when wet, brownish yellow when moist. Weak indication
- BedrockCr Weathered bedrock about 16 to 36 in down: no clay layer to dig. Weak indication
- BedrockRbest layer Unweathered bedrock about 36 to 80 in down: no clay layer to dig. Weak indication
What it looks like raw
The bedrock (R), 36 to 80 in down in the typical profile: hard fractured argillite. Raw colour is not fired colour.
About the soil
- Parent material: residuum weathered from metavolcanics and/or argillite.
- USDA family mineralogy: siliceous.
- USDA family particle-size class: loamy-skeletal.
- Drainage: well drained.
- Paralithic bedrock typically about 16 in (41 cm) down.
Where it is mapped
Seen on the map as the most common soil in 6 map units in North Carolina, in these survey areas: Davidson County, North Carolina; Montgomery County, North Carolina; Moore County, North Carolina; Randolph County, North Carolina.
By state: wild clay in North Carolina.
USDA, distribution and extent: The Southern Piedmont of Georgia, North Carolina, South Carolina, and Virginia. The series is extensive.
USDA, geographic setting: Goldston soils are on narrow gently rolling interstream ridges and sloping to steep sides of ridges between intermittent and perennial streams in the southern Piedmont. Slopes are dominantly from 4 to 25 percent but range from 2 to 60 percent. These soils formed in residuum weathered from felsic slates. Mean annual precipitation is about 47 inches and mean annual temperature about 60 degrees F., near the type location.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Badin: Strong lead
- Appling: Strong lead
- Cecil: Strong lead
- Davidson: Strong lead
- Iredell: Strong lead
- Mecklenburg: Strong lead
- Pacolet: Strong lead
- Vance: Strong lead
See it on the map
Open a Goldston spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Goldston very channery silt loam, 4 to 15 percent slopes, map unit GnD in Davidson County, North Carolina.
- Official Series Description: Goldston(revised 10/2021), established.
- Taxonomic class: Loamy-skeletal, siliceous, semiactive, thermic, shallow Typic Dystrudepts
- Rated with rule version 2026-09-28.1; the method is on the About page.