Escalante soil
Wild-clay potential
Weak indication
Weak indication: no layer of Escalante shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Escalante soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Escalante spot on the map
Rated from the USDA soil survey record for Escalante sandy loam, 1 to 12 percent slopes (Owyhee County Area, Idaho) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 10% clay.
- Lowers the potential Low engineering plasticity index (6): little plastic behavior expected when wet.
- Note The official series description calls the wet soil slightly sticky and slightly plastic.
- Note Thick enough to investigate (about 28 in (71 cm)).
- Note Typically starts within about 8 in (20 cm) of the surface.
- Note Few rock fragments (about 4% by volume).
- Note USDA reports about 28% calcium carbonate; lime in a clay body deserves testing.
Layer by layer
- TopsoilA A sandy loam layer about 0 to 8 in down: about 14% clay, moderate plasticity when wet, pale brown when moist. Weak indication
- Sandy layerBkbest layer A sandy loam layer about 8 to 36 in down: about 10% clay, low plasticity when wet, pink when moist. Weak indication
- Sandy layerC A loamy sand layer about 36 to 60 in down: about 6% clay, low plasticity when wet, brown when moist. Weak indication
What it looks like raw
The sandy layer (Bk), 8 to 36 in down in the typical profile: pink (7.5YR 7/4), brown (7.5YR 4/4) moist; hard, firm, slightly sticky and slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: mixed alluvium and/or lacustrine deposits and/or eolian sands.
- USDA family mineralogy: mixed.
- USDA family particle-size class: coarse-loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 2 map units in Idaho, in these survey areas: Owyhee County Area, Idaho.
By state: wild clay in Idaho.
USDA, distribution and extent: Southwestern Utah and Southern Idaho. This series is extensive. MLRAs 11, 25, 28A.
USDA, geographic setting: Parent material: Alluvium derived from igneous and sedimentary rocks
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Chilcott: Strong lead
- Fairylawn: Strong lead
- Perla: Strong lead
- Ratsnest: Strong lead
- Succor: Strong lead
- Arbidge: Promising
- Babbington: Promising
- Gooding: Promising
See it on the map
Open a Escalante spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 75%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Escalante sandy loam, 1 to 12 percent slopes, map unit 54 in Owyhee County Area, Idaho.
- Official Series Description: Escalante(revised 05/2012), established.
- Taxonomic class: Coarse-loamy, mixed, superactive, mesic Xeric Haplocalcids
- Rated with rule version 2026-09-28.1; the method is on the About page.