Bruncan soil
Wild-clay potential
Weak indication
Weak indication: no layer of Bruncan shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Bruncan soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Bruncan spot on the map
Rated from the USDA soil survey record for Bruncan very stony silt loam, 2 to 15 percent slopes (Owyhee County Area, Idaho) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clay-enriched layer: about 28% clay in the fine-earth portion.
- Note USDA labels this a "Bt" horizon: a subsoil layer where clay has accumulated.
- Note Moderate engineering plasticity index (19).
- Lowers the potential The official series description calls the wet soil slightly sticky and nonplastic.
- Note Thick enough to investigate (about 12 in (31 cm)).
- Note Typically starts within about 4 in (10 cm) of the surface.
- Lowers the potential Noticeable rock fragments (about 23% by volume); screening would be needed and the clay percentage applies to the fine earth only.
- Note USDA reports about 5% calcium carbonate; lime in a clay body deserves testing.
Layer by layer
- TopsoilA A very stony silt loam layer about 0 to 4 in down: about 21% clay, moderate plasticity when wet, pale brown when moist. Weak indication
- Clay subsoilBtbest layer A gravelly clay loam layer about 4 to 16 in down: about 28% clay, moderate plasticity when wet, pale brown when moist. Weak indication
- Clay subsoilBtk A very cobbly loam layer about 16 to 20 in down: about 20% clay, moderate plasticity when wet, very pale brown when moist. Weak indication
- Bkqm A cemented material layer about 20 to 26 in down: USDA gives no clay percentage or texture for it. Not enough data
- BedrockR Bedrock about 26 to 36 in down: no clay layer to dig. Weak indication
What it looks like raw
The clay subsoil (Bt), 4 to 16 in down in the typical profile: pale brown (10Y 6/3), dark yellowish brown (10YR 4/4) moist; soft, very friable, slightly sticky and nonplastic. Raw colour is not fired colour.
About the soil
- Parent material: volcanic ash and/or loess and mixed alluvium over bedrock derived from volcanic rock.
- USDA family mineralogy: mixed.
- USDA family particle-size class: loamy.
- Drainage: well drained.
- Lithic bedrock typically about 26 in (66 cm) down.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Idaho, in these survey areas: Owyhee County Area, Idaho.
By state: wild clay in Idaho.
USDA, distribution and extent: Southwestern Idaho and Southeastern Oregon. Bruncan soils are extensive. MLRA 25.
USDA, geographic setting: Bruncan soils are nearly level to rolling on tablelands, calderas, structural benches, plains and buttes at elevations of 825 to 1,795 meters. Slopes range from 0 to 15 percent. These soils formed in mixed silty alluvium and loess from basalt and volcanic ash. The climate is cool and moist in the winter and warm and dry in the summer. Average annual precipitation ranges from 200 to 360 mm. Average annual temperature ranges from 7.2 to 11.1 degrees C. Frost-free period is 80 to 145 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Chilcott: Strong lead
- Fairylawn: Strong lead
- Perla: Strong lead
- Ratsnest: Strong lead
- Succor: Strong lead
- Arbidge: Promising
- Babbington: Promising
- Gooding: Promising
See it on the map
Open a Bruncan spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 75%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Bruncan very stony silt loam, 2 to 15 percent slopes, map unit 25 in Owyhee County Area, Idaho.
- Official Series Description: Bruncan(revised 10/2018), established.
- Taxonomic class: Loamy, mixed, superactive, mesic, shallow Xeric Argidurids
- Rated with rule version 2026-09-28.1; the method is on the About page.