Athena soil
Wild-clay potential
Possible
Possible: a loamy layer with some clay typically about 10 to 30 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Athena soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Athena silt loam, 7 to 25 percent slopes, eroded (Whitman County, Washington) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 19% clay. It may need settling or refining to become a clay body.
- Note Moderate engineering plasticity index (14).
- Note The official series description calls the wet soil slightly sticky and slightly plastic.
- Note Thick enough to investigate (about 20 in (51 cm)).
- Note Typically starts within about 10 in (25 cm) of the surface.
- Missing data Rock fragment content is not reported.
Layer by layer
- TopsoilAp A silt loam layer about 0 to 10 in down: about 18% clay, moderate plasticity when wet, dark grayish brown when moist. Weak indication
- Loamy layerBw1best layer A silt loam layer about 10 to 30 in down: about 19% clay, moderate plasticity when wet, brown when moist. Possible
- Loamy layerBw2 A silt loam layer about 30 to 48 in down: about 19% clay, moderate plasticity when wet, light yellowish brown when moist. Possible
- Loamy layerBk A silt loam layer about 48 to 59 in down: about 18% clay, moderate plasticity when wet, light yellowish brown when moist. Weak indication
What it looks like raw
The loamy layer (Bw1), 10 to 30 in down in the typical profile: brown (10YR 5/3) dry, dark brown (10YR 3/3) moist; hard, friable, slightly sticky and slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: Loess with an insignificant amount of volcanic ash in the upper part.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-silty.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 10 map units in Idaho, Washington, in these survey areas: Latah County, Idaho; Lewis and Nez Perce Counties, Idaho; Whitman County, Washington.
By state: wild clay in Idaho,wild clay in Washington.
USDA, distribution and extent: Southeastern Washington, northeastern Oregon, and north-central Idaho; MLRA 9; extensive
USDA, geographic setting: Elevation--455 to 915 m
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Garfield: Strong lead
- Latah: Strong lead
- Tilma: Strong lead
- Cramont: Strong lead
- Driscoll: Strong lead
- Konert: Strong lead
- Taney: Strong lead
- Naff: Promising
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Athena silt loam, 7 to 25 percent slopes, eroded, map unit 10 in Whitman County, Washington.
- Official Series Description: Athena(revised 05/2017), established.
- Taxonomic class: Fine-silty, mixed, superactive, mesic Pachic Haploxerolls
- Rated with rule version 2026-09-28.1; the method is on the About page.