Wyman soil
Wild-clay potential
Possible
Possible: a loamy layer with some clay typically about 12 to 36 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Wyman soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Wyman fine sandy loam, 8 to 15 percent slopes, eroded (Western Riverside Area, California) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 25% clay. It may need settling or refining to become a clay body.
- Note Moderate engineering plasticity index (15).
- Raises the potential The official series description calls the wet soil moderately sticky and moderately plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 24 in (61 cm)).
- Note Typically starts within about 12 in (30 cm) of the surface.
- Note Few rock fragments (about 2% by volume).
Layer by layer
- Sandy layerH1 A fine sandy loam layer about 0 to 12 in down: about 15% clay, low plasticity when wet, brown when moist. Weak indication
- Loamy layerH2best layer A clay loam layer about 12 to 36 in down: about 25% clay, moderate plasticity when wet, brown when moist. Possible
- Loamy layerH3 A stratified loam to clay loam layer about 36 to 60 in down: about 25% clay, moderate plasticity when wet, brown when moist. Possible
What it looks like raw
The loamy layer (H2), 12 to 36 in down in the typical profile: brown (7.5YR 5/4), dark brown (7.5YR 4/4) moist; hard, friable, sticky and plastic. Raw colour is not fired colour.
About the soil
- Parent material: alluvium derived from igneous rock.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 2 map units in California, in these survey areas: Western Riverside Area, California.
By state: wild clay in California.
USDA, distribution and extent: Mostly along the eastern side of the San Joaquin Valley and small intermountain valleys of Southern California. The soils are moderately extensive.
USDA, geographic setting: Wyman soil are on old stream terraces and old alluvial fans. Slopes are 0 to 15 percent. The soils formed in alluvium originating from andesitic and basaltic rocks. Wyman soils occur at elevations of 300 to 2,500 feet. The climate is subhumid mesothermal having hot, dry summers and cool, moist winters. The mean annual precipitation is 9 to 25 inches. The average January temperature is 43 degrees F. and the average July temperature is about 62 degrees F. The frost free season is 200 to 300 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Altamont: Strong lead
- Auld: Strong lead
- Bosanko: Strong lead
- Las Posas: Strong lead
- Madera: Strong lead
- Murrieta: Strong lead
- Placentia: Strong lead
- Porterville: Strong lead
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Wyman fine sandy loam, 8 to 15 percent slopes, eroded, map unit WxD2 in Western Riverside Area, California.
- Official Series Description: Wyman(revised 01/2003), established.
- Taxonomic class: Fine-loamy, mixed, superactive, thermic Typic Haploxeralfs
- Rated with rule version 2026-09-28.1; the method is on the About page.