Toddstav soil
Wild-clay potential
Possible
Possible: a loamy layer with some clay typically about 7 to 55 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Toddstav soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Toddstav spot on the map
Rated from the USDA soil survey record for Toddstav silt loam, 0 to 4 percent slopes (Spotsylvania County, Virginia) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 27% clay. It may need settling or refining to become a clay body.
- Note Moderate engineering plasticity index (10).
- Note The official series description calls the wet soil slightly sticky and slightly plastic.
- Note Thick enough to investigate (about 48 in (122 cm)).
- Note Typically starts within about 7 in (18 cm) of the surface.
- Note Few rock fragments (about 2% by volume).
Layer by layer
- Sandy layerH1 A silt loam layer about 0 to 7 in down: about 14% clay, low plasticity when wet, gray when moist. Weak indication
- Loamy layerH2best layer A loam layer about 7 to 55 in down: about 27% clay, moderate plasticity when wet, gray when moist. Possible
- Sandy layerH3 A loam layer about 55 to 70 in down: about 17% clay, low plasticity when wet, light gray when moist. Weak indication
What it looks like raw
The loamy layer (H2), 7 to 55 in down in the typical profile: gray (10YR 5/1); friable, slightly sticky, slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: alluvium.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-silty.
- Drainage: poorly drained.
- Rated hydric (wetland) soil; often saturated and protected.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Virginia, in these survey areas: Spotsylvania County, Virginia.
By state: wild clay in Virginia.
USDA, distribution and extent: The Toddstav soils are not extensive. They are thought to occur on the southern mesic Piedmont Province of Virginia and North Carolina.
USDA, geographic setting: The Toddstav soils are along poorly defined drainageways in the mesic Piedmont Province. Slopes are commonly concave and range in gradient from 0 to 7 percent. The soils formed in silty colluvial and alluvial materials derived from mica schist.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Appling: Strong lead
- Brockroad: Strong lead
- Catharpin: Strong lead
- Cecil: Strong lead
- Cullen: Strong lead
- Dogue: Strong lead
- Fluvanna: Strong lead
- Masada: Strong lead
See it on the map
Open a Toddstav spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Toddstav silt loam, 0 to 4 percent slopes, map unit 42B in Spotsylvania County, Virginia.
- Official Series Description: Toddstav(revised 02/2000), established.
- Taxonomic class: Fine-silty, mixed, active, mesic Typic Endoaquults
- Rated with rule version 2026-09-28.1; the method is on the About page.