Roanoke soil
Wild-clay potential
Strong lead
Strong lead: a clayey layer typically about 9 to 53 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Roanoke soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Roanoke spot on the map
Rated from the USDA soil survey record for Roanoke silt loam, 0 to 2 percent slopes (Stafford and King George Counties, Virginia) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 48% clay in the fine-earth portion.
- Raises the potential High engineering plasticity index (30): USDA's estimate suggests plastic behavior when wet.
- Raises the potential The official series description calls the wet soil moderately sticky and moderately plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 44 in (112 cm)).
- Note Typically starts within about 9 in (23 cm) of the surface.
- Note Few rock fragments (about 3% by volume).
Layer by layer
- Loamy layerH1 A silt loam layer about 0 to 9 in down: about 19% clay, moderate plasticity when wet, dark grayish brown when moist. Possible
- Clay-rich layerH2best layer A clay layer about 9 to 53 in down: about 48% clay, high plasticity when wet, gray when moist. Strong lead
- Sandy layerH3 A fine sandy loam layer about 53 to 90 in down: about 15% clay, moderate plasticity when wet, gray when moist. Weak indication
- Sandy layerH4 A sand layer about 90 to 116 in down: about 5% clay, low plasticity when wet. Weak indication
What it looks like raw
The clay-rich layer (H2), 9 to 53 in down in the typical profile: gray (N 6/0); firm, moderately sticky, moderately plastic. Raw colour is not fired colour.
About the soil
- Parent material: alluvium.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine.
- Drainage: poorly drained.
- Rated hydric (wetland) soil; often saturated and protected.
Where it is mapped
Seen on the map as the most common soil in 2 map units in Georgia, Virginia, in these survey areas: Cobb County, Georgia; Stafford and King George Counties, Virginia.
By state: wild clay in Georgia,wild clay in Virginia.
USDA, distribution and extent: Distribution: Southern piedmont and the upper and middle coastal plain in Virginia, Alabama, Georgia, North Carolina, and South Carolina
USDA, geographic setting: Landscape: Piedmont
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Appling: Strong lead
- Cecil: Strong lead
- Bladen: Strong lead
- Caroline: Strong lead
- Craven: Strong lead
- Cullen: Strong lead
- Dogue: Strong lead
- Elbert: Strong lead
See it on the map
Open a Roanoke spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Roanoke silt loam, 0 to 2 percent slopes, map unit Ro in Stafford and King George Counties, Virginia.
- Official Series Description: Roanoke(revised 04/2006), established.
- Taxonomic class: Fine, mixed, semiactive, thermic Typic Endoaquults
- Rated with rule version 2026-09-28.1; the method is on the About page.