Elbert soil
Wild-clay potential
Strong lead
Strong lead: a clayey layer typically about 10 to 35 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Elbert soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Elbert silt loam, thin solum variant (Stafford and King George Counties, Virginia) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 50% clay in the fine-earth portion.
- Raises the potential High engineering plasticity index (41): USDA's estimate suggests plastic behavior when wet.
- Raises the potential The official series description calls the wet soil moderately sticky and moderately plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 25 in (64 cm)).
- Note Typically starts within about 10 in (25 cm) of the surface.
- Note Few rock fragments (about 3% by volume).
- Note High shrink-swell (linear extensibility about 7.5%): often very plastic, and prone to cracking as it dries.
- Note Engineering class CH: a clay of high plasticity in the Unified system.
Layer by layer
- Loamy layerH1 A silt loam layer about 0 to 10 in down: about 21% clay, moderate plasticity when wet, light gray to gray when moist. Possible
- Clay-rich layerH2best layer A clay layer about 10 to 35 in down: about 50% clay, high plasticity when wet, dark gray when moist. Strong lead
- Loamy layerH3 A loam layer about 35 to 64 in down: about 25% clay, high plasticity when wet, dark grayish brown when moist. Possible
- Sandy layerH4 A gravelly loamy sand layer about 64 to 90 in down: about 8% clay, moderate plasticity when wet, variegated light olive brown when moist. Weak indication
- BedrockH5 Bedrock about 90 to 94 in down: no clay layer to dig. Weak indication
What it looks like raw
The clay-rich layer (H2), 10 to 35 in down in the typical profile: dark gray (5Y 4/1); very firm; sticky, plastic. Raw colour is not fired colour.
About the soil
- Parent material: mixed mafic residuum.
- USDA family mineralogy: smectitic. Smectite-rich clays are usually very plastic and shrink a lot as they dry.
- USDA family particle-size class: fine.
- Drainage: poorly drained.
- Paralithic bedrock typically about 90 in (228 cm) down.
- Rated hydric (wetland) soil; often saturated and protected.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Virginia, in these survey areas: Stafford and King George Counties, Virginia.
By state: wild clay in Virginia.
USDA, distribution and extent: Virginia; possibly Maryland and North Carolina.
USDA, geographic setting: Elbert soils are on nearly level to gently sloping upland flats, depressions, and drainageways with slope gradients mostly between 0 to 5 percent. Drainageways are subject to frequent, extremely brief, flash flooding events with little or no deposition or erosion. They formed in local alluvium over residuum. The regolith is clayey residuum from dark colored basic rocks such as greenstone, diorite, hornblende, gneiss, dacite, or local colluvium of similar origin. Mean annual temperature ranges from about 53 degrees to 59 degrees F and the mean annual precipitation ranges from about 35 to 45 inches.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Appling: Strong lead
- Bladen: Strong lead
- Caroline: Strong lead
- Cecil: Strong lead
- Craven: Strong lead
- Cullen: Strong lead
- Dogue: Strong lead
- Lignum: Strong lead
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Elbert silt loam, thin solum variant, map unit Eb in Stafford and King George Counties, Virginia.
- Official Series Description: Elbert(revised 02/2022), established.
- Taxonomic class: Fine, smectitic, mesic Typic Endoaqualfs
- Rated with rule version 2026-09-28.1; the method is on the About page.