Prue soil
Wild-clay potential
Strong lead
Strong lead: a clay-enriched layer typically about 39 to 50 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Prue soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Prue loam, 3 to 5 percent slopes (Osage County, Oklahoma) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 38% clay in the fine-earth portion.
- Note USDA labels this a "2Bt2" horizon: a subsoil layer where clay has accumulated.
- Raises the potential High engineering plasticity index (27): USDA's estimate suggests plastic behavior when wet.
- Note Moderate thickness (about 11 in (28 cm)).
- Note Typically starts about 39 in (99 cm) down; expect real digging or look for cuts and banks.
- Missing data Rock fragment content is not reported.
Layer by layer
- TopsoilA A loam layer about 0 to 12 in down: about 22% clay, moderate plasticity when wet, very dark brown when moist. Possible
- Loamy layerBA A loam layer about 12 to 18 in down: about 26% clay, moderate plasticity when wet, very dark grayish brown when moist. Possible
- Clay subsoilBt1 A sandy clay loam layer about 18 to 39 in down: about 31% clay, high plasticity when wet, yellowish brown when moist. Promising
- Clay subsoil2Bt2best layer A silty clay loam layer about 39 to 50 in down: about 38% clay, high plasticity when wet, yellowish brown when moist. Strong lead
- Clay-rich layer2BC A silty clay layer about 50 to 72 in down: about 45% clay, high plasticity when wet, coarse redoximorphic features of strong brown when moist. Promising
- Bedrock2Cr Bedrock about 72 to 82 in down: no clay layer to dig. Weak indication
What it looks like raw
The clay subsoil (2Bt2), 39 to 50 in down in the typical profile: yellowish brown (10YR 5/4), light yellowish brown (10YR 6/4) dry; hard, friable. Raw colour is not fired colour.
About the soil
- Parent material: loamy colluvium derived from sandstone and shale.
- USDA family mineralogy: siliceous.
- USDA family particle-size class: fine-loamy.
- Drainage: moderately well drained.
- Paralithic bedrock typically about 72 in (183 cm) down.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Oklahoma, in these survey areas: Osage County, Oklahoma.
By state: wild clay in Oklahoma.
USDA, distribution and extent: General area: Northeastern Oklahoma and southeast Kansas
USDA, geographic setting: Parent Material: colluvial sediments weathered from interbedded sandstone and shale of Pennsylvanian age
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Agra: Strong lead
- Bethany: Strong lead
- Grainola: Strong lead
- Niotaze: Strong lead
- Parsons: Strong lead
- Steedman: Strong lead
- Wynona: Strong lead
- Barnsdall: Promising
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Prue loam, 3 to 5 percent slopes, map unit 51 in Osage County, Oklahoma.
- Official Series Description: Prue(revised 09/2020), established.
- Taxonomic class: Fine-loamy, siliceous, active, thermic Mollic Paleudalfs
- Rated with rule version 2026-09-28.1; the method is on the About page.