Barnsdall soil
Wild-clay potential
Promising
Promising: a clay-enriched layer typically about 11 to 29 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Barnsdall soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Barnsdall spot on the map
Rated from the USDA soil survey record for Barnsdall very fine sandy loam, 0 to 1 percent slopes, rarely flooded (Osage County, Oklahoma) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clay-enriched layer: about 31% clay in the fine-earth portion.
- Note USDA labels this a "Bt1" horizon: a subsoil layer where clay has accumulated.
- Note Moderate engineering plasticity index (16).
- Note Thick enough to investigate (about 18 in (46 cm)).
- Note Typically starts within about 11 in (28 cm) of the surface.
- Missing data Rock fragment content is not reported.
Layer by layer
- TopsoilAp A very fine sandy loam layer about 0 to 7 in down: about 15% clay, low plasticity when wet. Weak indication
- Loamy layerE A very fine sandy loam layer about 7 to 11 in down: about 18% clay, low plasticity when wet. Weak indication
- Clay subsoilBt1best layer A silty clay loam layer about 11 to 29 in down: about 31% clay, moderate plasticity when wet. Promising
- Clay subsoilBt2 A silty clay loam layer about 29 to 45 in down: about 31% clay, moderate plasticity when wet. Promising
- Loamy layerBC A clay loam layer about 45 to 58 in down: about 29% clay, moderate plasticity when wet, reddish brown when moist. Promising
- Loamy layer2C A fine sandy loam layer about 58 to 72 in down: about 18% clay, moderate plasticity when wet, brown when moist. Weak indication
What it looks like raw
The clay subsoil (Bt1), 11 to 29 in down in the typical profile: hard, friable. Raw colour is not fired colour.
About the soil
- Parent material: loamy alluvium derived from sedimentary rock over sandy alluvium derived from sedimentary rock.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-silty.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Oklahoma, in these survey areas: Osage County, Oklahoma.
By state: wild clay in Oklahoma.
USDA, distribution and extent: Eastern Oklahoma and possibly southeastern Kansas. The series is of minor extent.
USDA, geographic setting: The Barnsdall soils occur on nearly level flood plains.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Agra: Strong lead
- Bethany: Strong lead
- Grainola: Strong lead
- Niotaze: Strong lead
- Parsons: Strong lead
- Prue: Strong lead
- Steedman: Strong lead
- Wynona: Strong lead
See it on the map
Open a Barnsdall spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 80%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Barnsdall very fine sandy loam, 0 to 1 percent slopes, rarely flooded, map unit 3 in Osage County, Oklahoma.
- Official Series Description: Barnsdall(revised 05/2005), established.
- Taxonomic class: Fine-silty, mixed, active, thermic Ultic Hapludalfs
- Rated with rule version 2026-09-28.1; the method is on the About page.