Kempsville soil
Wild-clay potential
Possible
Possible: a loamy layer with some clay typically about 10 to 54 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Kempsville soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Kempsville spot on the map
Rated from the USDA soil survey record for Kempsville fine sandy loam, gravelly substratum, 2 to 6 percent slopes (Stafford and King George Counties, Virginia) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 25% clay. It may need settling or refining to become a clay body.
- Note Moderate engineering plasticity index (10).
- Note Thick enough to investigate (about 44 in (112 cm)).
- Note Typically starts within about 10 in (25 cm) of the surface.
- Note Few rock fragments (about 11% by volume).
Layer by layer
- Sandy layerH1 A fine sandy loam layer about 0 to 10 in down: about 10% clay, low plasticity when wet, light yellowish brown when moist. Weak indication
- Loamy layerH2best layer A sandy clay loam layer about 10 to 54 in down: about 25% clay, moderate plasticity when wet, yellowish brown when moist. Possible
- Sandy layerH3 A fine sandy loam layer about 54 to 72 in down: about 15% clay, low plasticity when wet, yellowish brown when moist. Weak indication
- Sandy layerH4 A gravelly loamy fine sand layer about 72 to 76 in down: about 8% clay, low plasticity when wet. Weak indication
What it looks like raw
The loamy layer (H2), 10 to 54 in down in the typical profile: yellowish brown (10YR 5/6). Raw colour is not fired colour.
About the soil
- Parent material: loamy marine deposits.
- USDA family mineralogy: siliceous.
- USDA family particle-size class: fine-loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 5 map units in Virginia, in these survey areas: Prince William County, Virginia; Stafford and King George Counties, Virginia.
By state: wild clay in Virginia.
USDA, distribution and extent: Eastern Virginia, southern Maryland, northern North Carolina, and possibly Tennessee. The series is of moderate extent.
USDA, geographic setting: Kempsville soils are on nearly level to moderately steep Coastal Plain uplands. Slopes are dominantly 0 to 6 percent, but range from 0 to 25 percent. These soils formed in loamy fluvial and marine sediments. Mean annual temperature ranges from 58 to 62 degrees F and mean annual precipitation ranges from 41 to 49 inches.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Appling: Strong lead
- Caroline: Strong lead
- Cecil: Strong lead
- Susquehanna: Strong lead
- Worsham: Strong lead
- Aden: Strong lead
- Albano: Strong lead
- Bladen: Strong lead
See it on the map
Open a Kempsville spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Kempsville fine sandy loam, gravelly substratum, 2 to 6 percent slopes, map unit KfB in Stafford and King George Counties, Virginia.
- Official Series Description: Kempsville(revised 02/2010), established.
- Taxonomic class: Fine-loamy, siliceous, subactive, thermic Typic Hapludults
- Rated with rule version 2026-09-28.1; the method is on the About page.