Colby soil
Wild-clay potential
Promising
Promising: a loamy layer with some clay typically about 12 to 43 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Colby soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Colby silty clay loam, 1 to 3 percent slopes (Boulder County Area, Colorado) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clay-enriched layer: about 31% clay in the fine-earth portion.
- Note Moderate engineering plasticity index (10).
- Note Thick enough to investigate (about 31 in (79 cm)).
- Note Typically starts within about 12 in (30 cm) of the surface.
- Missing data Rock fragment content is not reported.
- Note USDA reports about 8% calcium carbonate; lime in a clay body deserves testing.
Layer by layer
- Loamy layerH1 A silty clay loam layer about 0 to 12 in down: about 31% clay, moderate plasticity when wet, grayish brown when moist. Promising
- Loamy layerH2best layer A silty clay loam layer about 12 to 43 in down: about 31% clay, moderate plasticity when wet, very pale brown when moist. Promising
- Loamy layerH3 A clay loam layer about 43 to 60 in down: about 31% clay, moderate plasticity when wet, very pale brown when moist. Promising
What it looks like raw
The loamy layer (H2), 12 to 43 in down in the typical profile: very pale brown (10YR 7/3), light yellowish brown (10YR 6/4) moist; slightly hard, friable. Raw colour is not fired colour.
About the soil
- Parent material: uniform eolian deposits.
- USDA family particle-size class: fine-silty.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 7 map units in Colorado, in these survey areas: Boulder County Area, Colorado; Weld County, Colorado, Southern Part.
By state: wild clay in Colorado.
USDA, distribution and extent: Western Kansas, eastern Colorado, western Nebraska, southwestern South Dakota, and eastern Montana in MLRA 64, 67, and 72. The series is extensive.
USDA, geographic setting: Parent material: loess
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Heldt: Strong lead
- Nunn: Strong lead
- Renohill: Strong lead
- Weld: Strong lead
- Denver: Strong lead
- Englewood: Strong lead
- Gaynor: Strong lead
- Kutch: Strong lead
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 90%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Colby silty clay loam, 1 to 3 percent slopes, map unit CoB in Boulder County Area, Colorado.
- Official Series Description: Colby(revised 07/2012), established.
- Taxonomic class: Fine-silty, mixed, superactive, calcareous, mesic Aridic Ustorthents
- Rated with rule version 2026-09-28.1; the method is on the About page.