Heldt soil
Wild-clay potential
Strong lead
Strong lead: a clayey layer typically about 7 to 60 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Heldt soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Heldt silty clay, 1 to 3 percent slopes (Weld County, Colorado, Southern Part) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 48% clay in the fine-earth portion.
- Raises the potential High engineering plasticity index (20): USDA's estimate suggests plastic behavior when wet.
- Raises the potential The official series description calls the wet soil very sticky and very plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 53 in (134 cm)).
- Note Typically starts within about 7 in (18 cm) of the surface.
- Missing data Rock fragment content is not reported.
- Note High shrink-swell (linear extensibility about 7.5%): often very plastic, and prone to cracking as it dries.
- Note USDA reports about 8% calcium carbonate; lime in a clay body deserves testing.
Layer by layer
- Clay-rich layerH1 A silty clay layer about 0 to 7 in down: about 48% clay, high plasticity when wet, light brownish gray when moist. Strong lead
- Clay-rich layerH2best layer A silty clay layer about 7 to 60 in down: about 48% clay, high plasticity when wet, light brownish gray when moist. Strong lead
What it looks like raw
The clay-rich layer (H2), 7 to 60 in down in the typical profile: light brownish gray (2.5Y 6/2), grayish brown (2.5Y 5/2) moist; extremely hard, friable, very sticky and very plastic. Raw colour is not fired colour.
About the soil
- Parent material: sediment alluvium derived from shale.
- USDA family mineralogy: smectitic. Smectite-rich clays are usually very plastic and shrink a lot as they dry.
- USDA family particle-size class: fine.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 4 map units in Colorado, in these survey areas: Boulder County Area, Colorado; Weld County, Colorado, Southern Part.
By state: wild clay in Colorado.
USDA, distribution and extent: Central and northern Wyoming, southern Montana, and northern Colorado. The series is of moderate extent.
USDA, geographic setting: The Heldt soils are on fan remnants terraces, hillslopes and alluvial fans. Slopes range from 0 to 25 percent. The soils formed in fine textured alluvial sediments derived primarily from sedimentary rock. The average annual precipitation is 10 to 15 inches with over half falling in the months of April, May, and June. The average annual temperature is 44 to 48 degrees F. The frost-free season is 110 to 140 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Nunn: Strong lead
- Renohill: Strong lead
- Weld: Strong lead
- Denver: Strong lead
- Englewood: Strong lead
- Gaynor: Strong lead
- Kutch: Strong lead
- Longmont: Strong lead
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Heldt silty clay, 1 to 3 percent slopes, map unit 27 in Weld County, Colorado, Southern Part.
- Official Series Description: Heldt(revised 04/2003), established.
- Taxonomic class: Fine, smectitic, mesic Ustertic Haplocambids
- Rated with rule version 2026-09-28.1; the method is on the About page.