Weld soil
Wild-clay potential
Strong lead
Strong lead: a clay-enriched layer typically about 17 to 31 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Weld soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Weld loamy sand, 0 to 3 percent slopes (Boulder County Area, Colorado) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 42% clay in the fine-earth portion.
- Note USDA labels this a "Btk" horizon: a subsoil layer where clay has accumulated.
- Raises the potential High engineering plasticity index (29): USDA's estimate suggests plastic behavior when wet.
- Note Thick enough to investigate (about 14 in (35 cm)).
- Note Typically starts within about 17 in (43 cm) of the surface.
- Missing data Rock fragment content is not reported.
- Note High shrink-swell (linear extensibility about 7.1%): often very plastic, and prone to cracking as it dries.
- Note USDA reports about 5% calcium carbonate; lime in a clay body deserves testing.
- Note Engineering class CH: a clay of high plasticity in the Unified system.
Layer by layer
- TopsoilA A loamy sand layer about 0 to 12 in down: about 5% clay, low plasticity when wet, grayish brown when moist. Weak indication
- Clay subsoilBt A silty clay layer about 12 to 17 in down: about 42% clay, high plasticity when wet, brown when moist. Promising
- Clay subsoilBtkbest layer A silty clay layer about 17 to 31 in down: about 42% clay, high plasticity when wet, light brownish gray when moist. Strong lead
- Loamy layerBk A silt loam layer about 31 to 60 in down: about 22% clay, moderate plasticity when wet, light brownish gray when moist. Possible
- Loamy layerC A silt loam layer about 60 to 80 in down: about 19% clay, moderate plasticity when wet, pale brown when moist. Weak indication
What it looks like raw
The clay subsoil (Btk), 17 to 31 in down in the typical profile: light brownish gray (10YR 6/2), brown (10YR 5/3) moist. Raw colour is not fired colour.
About the soil
- Parent material: eolian sands over calcareous loess.
- USDA family mineralogy: smectitic. Smectite-rich clays are usually very plastic and shrink a lot as they dry.
- USDA family particle-size class: fine.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 7 map units in Colorado, in these survey areas: Boulder County Area, Colorado; Weld County, Colorado, Southern Part.
By state: wild clay in Colorado.
USDA, distribution and extent: Present known distribution limited to eastern Colorado and Wyoming. Series is of large extent. MLRA's 67 and 69.
USDA, geographic setting: Landform: on hills, plains and interfluves
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Heldt: Strong lead
- Nunn: Strong lead
- Renohill: Strong lead
- Denver: Strong lead
- Englewood: Strong lead
- Gaynor: Strong lead
- Kutch: Strong lead
- Longmont: Strong lead
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Weld loamy sand, 0 to 3 percent slopes, map unit WdB in Boulder County Area, Colorado.
- Official Series Description: Weld(revised 02/2006), established.
- Taxonomic class: Fine, smectitic, mesic Aridic Argiustolls
- Rated with rule version 2026-09-28.1; the method is on the About page.