Buncombe soil
Wild-clay potential
Weak indication
Weak indication: no layer of Buncombe shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Buncombe soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Buncombe spot on the map
Rated from the USDA soil survey record for Buncombe loamy sand, 0 to 6 percent slopes (Douglas County, Georgia) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 8% clay.
- Lowers the potential Low engineering plasticity index (0): little plastic behavior expected when wet.
- Note Thick enough to investigate (about 45 in (115 cm)).
- Note Typically starts within about 10 in (25 cm) of the surface.
- Note Few rock fragments (about 2% by volume).
Layer by layer
- Sandy layerH1 A loamy sand layer about 0 to 10 in down: about 8% clay, low plasticity when wet, brown when moist. Weak indication
- Sandy layerH2best layer A sand layer about 10 to 55 in down: about 8% clay, low plasticity when wet, brown when moist. Weak indication
- Sandy layerH3 A sandy loam layer about 55 to 65 in down: about 10% clay, low plasticity when wet, reddish brown when moist. Weak indication
What it looks like raw
The sandy layer (H2), 10 to 55 in down in the typical profile: brown (7.5YR 5/4); loose. Raw colour is not fired colour.
About the soil
- Parent material: alluvium.
- USDA family mineralogy: mixed.
- USDA family particle-size class: not used.
- Drainage: excessively drained.
Where it is mapped
Seen on the map as the most common soil in 3 map units in Georgia, in these survey areas: Cherokee, Gilmer, and Pickens Counties, Georgia; Douglas County, Georgia; Fulton County, Georgia.
By state: wild clay in Georgia.
USDA, distribution and extent: Alabama, Georgia, North Carolina, South Carolina, and Virginia. The series is of moderate extent.
USDA, geographic setting: Buncombe soils are on nearly level to gently sloping flood plains in the Piedmont and Coastal Plain, usually adjacent to stream channels. Slopes range from 0 to 6 percent. The soil formed in sandy alluvium. Mean annual air temperature ranges from 58 to 68 degrees F., and mean annual precipitation
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Appling: Strong lead
- Madison: Strong lead
- Helena: Strong lead
- Hiwassee: Strong lead
- Lloyd: Strong lead
- Cecil: Strong lead
- Davidson: Strong lead
- Enon: Strong lead
See it on the map
Open a Buncombe spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 100%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Buncombe loamy sand, 0 to 6 percent slopes, map unit Bfs in Douglas County, Georgia.
- Official Series Description: Buncombe(revised 05/2010), established.
- Taxonomic class: Mixed, thermic Typic Udipsamments
- Rated with rule version 2026-09-28.1; the method is on the About page.