Bremer soil
Wild-clay potential
Strong lead
Strong lead: a clay-enriched layer typically about 12 to 53 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Bremer soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Bremer silty clay loam, 0 to 2 percent slopes, rarely flooded (Pike County, Missouri) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 42% clay in the fine-earth portion.
- Note USDA labels this a "Btg" horizon: a subsoil layer where clay has accumulated.
- Raises the potential High engineering plasticity index (30): USDA's estimate suggests plastic behavior when wet.
- Note Thick enough to investigate (about 41 in (105 cm)).
- Note Typically starts within about 12 in (30 cm) of the surface.
- Missing data Rock fragment content is not reported.
- Note High shrink-swell (linear extensibility about 7.5%): often very plastic, and prone to cracking as it dries.
- Note Engineering class CH: a clay of high plasticity in the Unified system.
Layer by layer
- Clay-rich layerA A silty clay loam layer about 0 to 12 in down: about 36% clay, high plasticity when wet, black when moist. Strong lead
- Clay subsoilBtgbest layer A silty clay layer about 12 to 53 in down: about 42% clay, high plasticity when wet, dark grayish brown when moist. Strong lead
- Clay-rich layerBCg A silty clay loam layer about 53 to 60 in down: about 40% clay, high plasticity when wet, dark gray when moist. Promising
What it looks like raw
The clay subsoil (Btg), 12 to 53 in down in the typical profile: dark grayish brown (2.5Y 4/2); silty clay loam; firm. Raw colour is not fired colour.
About the soil
- Parent material: alluvium.
- USDA family mineralogy: smectitic. Smectite-rich clays are usually very plastic and shrink a lot as they dry.
- USDA family particle-size class: fine.
- Drainage: poorly drained.
- Rated hydric (wetland) soil; often saturated and protected.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Missouri, in these survey areas: Pike County, Missouri.
By state: wild clay in Missouri.
USDA, distribution and extent: Physiographic Division--Interior Plains
USDA, geographic setting: Parent material--alluvium
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Bucklick: Strong lead
- Carlow: Strong lead
- Chequest: Strong lead
- Crider: Strong lead
- Dupo: Strong lead
- Gorin: Strong lead
- Keswick: Strong lead
- Okaw: Strong lead
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 95%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Bremer silty clay loam, 0 to 2 percent slopes, rarely flooded, map unit 13507 in Pike County, Missouri.
- Official Series Description: Bremer(revised 10/2019), established.
- Taxonomic class: Fine, smectitic, mesic Typic Argiaquolls
- Rated with rule version 2026-09-28.1; the method is on the About page.