Bertie soil
Wild-clay potential
Promising
Promising: a loamy layer with some clay typically about 37 to 47 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Bertie soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Bertie very fine sandy loam, 0 to 3 percent slopes (Stafford and King George Counties, Virginia) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clay-enriched layer: about 30% clay in the fine-earth portion.
- Note Moderate engineering plasticity index (18).
- Note Moderate thickness (about 10 in (25 cm)).
- Note Typically starts about 37 in (94 cm) down; expect real digging or look for cuts and banks.
- Missing data Rock fragment content is not reported.
Layer by layer
- Sandy layerH1 A very fine sandy loam layer about 0 to 10 in down: about 10% clay, low plasticity when wet, dark grayish brown when moist. Weak indication
- Loamy layerH2 A sandy clay loam layer about 10 to 37 in down: about 27% clay, moderate plasticity when wet, gray when moist. Possible
- Loamy layerH3best layer A clay loam layer about 37 to 47 in down: about 30% clay, moderate plasticity when wet, gray when moist. Promising
- Sandy layerH4 A loamy fine sand layer about 47 to 70 in down: about 10% clay, low plasticity when wet, light yellowish brown when moist. Weak indication
What it looks like raw
The loamy layer (H3), 37 to 47 in down in the typical profile: gray (2.5Y 6/1); very friable. Raw colour is not fired colour.
About the soil
- Parent material: loamy marine deposits.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-loamy.
- Drainage: moderately well drained.
Where it is mapped
Seen on the map as the most common soil in 2 map units in Virginia, in these survey areas: Prince William County, Virginia; Stafford and King George Counties, Virginia.
By state: wild clay in Virginia.
USDA, distribution and extent: Distribution: Lower Coastal Plain of Virginia, South Carolina and North Carolina
USDA, geographic setting: Landscape: Coastal Plain
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Appling: Strong lead
- Caroline: Strong lead
- Cecil: Strong lead
- Susquehanna: Strong lead
- Worsham: Strong lead
- Aden: Strong lead
- Albano: Strong lead
- Bladen: Strong lead
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Bertie very fine sandy loam, 0 to 3 percent slopes, map unit BaA in Stafford and King George Counties, Virginia.
- Official Series Description: Bertie(revised 08/2008), established.
- Taxonomic class: Fine-loamy, mixed, semiactive, thermic Aeric Endoaquults
- Rated with rule version 2026-09-28.1; the method is on the About page.