Ashlar soil
Wild-clay potential
Weak indication
Weak indication: no layer of Ashlar shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Ashlar soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Ashlar fine sandy loam, 6 to 15 percent slopes (Stafford and King George Counties, Virginia) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 10% clay.
- Lowers the potential Low engineering plasticity index (2): little plastic behavior expected when wet.
- Note Thick enough to investigate (about 12 in (30 cm)).
- Note Typically starts within about 18 in (46 cm) of the surface.
- Lowers the potential Noticeable rock fragments (about 21% by volume); screening would be needed and the clay percentage applies to the fine earth only.
Layer by layer
- Sandy layerH1 A fine sandy loam layer about 0 to 9 in down: about 10% clay, low plasticity when wet. Weak indication
- Sandy layerH2 A fine sandy loam layer about 9 to 18 in down: about 10% clay, low plasticity when wet. Weak indication
- Sandy layerH3best layer A gravelly fine sandy loam layer about 18 to 30 in down: about 10% clay, low plasticity when wet. Weak indication
- BedrockH4 Bedrock about 30 to 40 in down: no clay layer to dig. Weak indication
What it looks like raw
The sandy layer (H3), 18 to 30 in down in the typical profile. Raw colour is not fired colour.
About the soil
- Parent material: residuum weathered from granite and gneiss.
- USDA family mineralogy: mixed.
- USDA family particle-size class: coarse-loamy.
- Drainage: well drained.
- Lithic bedrock typically about 30 in (76 cm) down.
Where it is mapped
Seen on the map as the most common soil in 9 map units in Georgia, North Carolina, Virginia, in these survey areas: DeKalb County, Georgia; Forsyth County, North Carolina; Fulton County, Georgia; Prince William County, Virginia; Stafford and King George Counties, Virginia.
By state: wild clay in Georgia,wild clay in North Carolina,wild clay in Virginia.
USDA, distribution and extent: Distribution: Piedmont of Virginia, Georgia, North Carolina, and possibly South Carolina
USDA, geographic setting: Landscape: Piedmont Plateau of the thermic Southern Piedmont
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Appling: Strong lead
- Cecil: Strong lead
- Hiwassee: Strong lead
- Madison: Strong lead
- Pacolet: Strong lead
- Caroline: Strong lead
- Enon: Strong lead
- Jackland: Strong lead
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Ashlar fine sandy loam, 6 to 15 percent slopes, map unit AsD in Stafford and King George Counties, Virginia.
- Official Series Description: Ashlar(revised 10/2021), established.
- Taxonomic class: Coarse-loamy, mixed, semiactive, thermic Typic Dystrudepts
- Rated with rule version 2026-09-28.1; the method is on the About page.