Ascalon soil
Wild-clay potential
Possible
Possible: a loamy layer with some clay typically about 19 to 35 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Ascalon soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Ascalon spot on the map
Rated from the USDA soil survey record for Ascalon sandy loam, 0 to 3 percent slopes (Weld County, Colorado, Southern Part) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 23% clay. It may need settling or refining to become a clay body.
- Note Moderate engineering plasticity index (12).
- Note Thick enough to investigate (about 16 in (41 cm)).
- Note Typically starts within about 19 in (48 cm) of the surface.
- Note Few rock fragments (about 0% by volume).
- Note USDA reports about 8% calcium carbonate; lime in a clay body deserves testing.
Layer by layer
- TopsoilAp A sandy loam layer about 0 to 6 in down: about 14% clay, moderate plasticity when wet, grayish brown when moist. Weak indication
- Clay subsoilBt1 A sandy clay loam layer about 6 to 12 in down: about 25% clay, moderate plasticity when wet, brown when moist. Possible
- Clay subsoilBt2 A sandy clay loam layer about 12 to 19 in down: about 25% clay, moderate plasticity when wet, brown when moist. Possible
- Loamy layerBkbest layer A sandy clay loam layer about 19 to 35 in down: about 23% clay, moderate plasticity when wet, light gray when moist. Possible
- Sandy layerC A sandy loam layer about 35 to 80 in down: about 14% clay, low plasticity when wet, pale yellow when moist. Weak indication
What it looks like raw
The loamy layer (Bk), 19 to 35 in down in the typical profile: light gray (2.5Y 7/2 ); hard, very friable. Raw colour is not fired colour.
About the soil
- Parent material: wind-reworked alluvium and/or calcareous sandy eolian deposits.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 10 map units in Colorado, in these survey areas: Boulder County Area, Colorado; Weld County, Colorado, Southern Part.
By state: wild clay in Colorado.
USDA, distribution and extent: Eastern Colorado, Nebraska, and Wyoming in MLRA's 67 and 69. The series is of large extent.
USDA, geographic setting: Parent material: thick, moderately coarse textured, calcareous material.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Heldt: Strong lead
- Nunn: Strong lead
- Renohill: Strong lead
- Weld: Strong lead
- Denver: Strong lead
- Englewood: Strong lead
- Gaynor: Strong lead
- Kutch: Strong lead
See it on the map
Open a Ascalon spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Ascalon sandy loam, 0 to 3 percent slopes, map unit 5 in Weld County, Colorado, Southern Part.
- Official Series Description: Ascalon(revised 09/2005), established.
- Taxonomic class: Fine-loamy, mixed, superactive, mesic Aridic Argiustolls
- Rated with rule version 2026-09-28.1; the method is on the About page.